Home/Chimney flashing leak

Roofing · Check the flashing first

Chimney flashing leak

A ceiling stain around a chimney is almost always flashing rather than masonry. The chimney-to-roof junction is the most common roof leak point on any house, and the fix depends on whether it was flashed the right way to begin with.

Quick answerIf you have a stain on the ceiling or wet framing around the chimney, suspect the flashing before the brick. Proper flashing is step flashing woven into each shingle course, with counter-flashing cut into the mortar joints and lapped over it. A continuous strip of caulked metal is the shortcut version and fails within a few years. The lasting fix is to reflash correctly, not to add more sealant.

A chimney is a box of masonry punched through the roof, and every side of it is a seam water can find. The roof and the chimney also move differently with temperature and settling, so the joint has to be built in overlapping layers that shed water without relying on a glued seal.

A chimney rising through a house roof, where flashing seals the joint between masonry and shingles
Every side of the chimney is a seam the flashing has to cover. Photo by Xin on Unsplash.

1Why chimney flashing leaks

  • Shortcut flashing. A single bent strip of metal stuck to the brick and the shingles with caulk or roofing cement looks finished from the ground. The sealant dries, cracks and lets go, usually within a few years.
  • Counter-flashing that was never cut in. Counter-flashing should be set into a mortar joint so water running down the brick lands on top of the step flashing. Metal that is only face-sealed to the brick lets water run behind it.
  • Flashing reused during a reroof. Replacing chimney flashing means cutting into the masonry, so it is often left in place and the new shingles are worked around it. Old, rusted or bent metal under a new roof is a common source of leaks.
  • Rust and wear. Steel flashing rusts through over time. Rust streaks below the chimney are a sign the metal is failing.
  • The uphill side. Water and debris collect on the high side of a chimney. Wider chimneys need a cricket, a small peaked diverter, to steer water around them.

2How to check what you’re dealing with

  1. Look from the ground with binocularsLook for one long strip of metal along each side, heavy smears of caulk or tar, metal lifting off the brick, or rust streaks below the chimney.
  2. Check the attic after rainWith a flashlight, look at the framing and decking right around the chimney. Dark staining, wet wood or drips that show up only in rain point to the roof junction.
  3. Note when it leaksA leak that shows up only in wind-driven rain from one direction often points to one side of the flashing. A leak in steady rain from any direction is more likely a general flashing failure or the crown.
  4. Rule out the masonryA cracked crown at the top or badly spalling brick can let water into the chimney itself. A roofer or chimney contractor can tell you which one is leaking.

3Fixing it

What a homeowner can do

  • Inspect from the ground and the attic
  • Photograph stains and note which storms cause them
  • Put a bucket under active drips and move belongings
  • Ask whether your flashing will be replaced at the next reroof

Hire a pro

  • Any work on the roof itself, especially on a steep pitch
  • Reflashing with step flashing and counter-flashing cut into the mortar
  • Adding a cricket on the uphill side of a wide chimney
  • Leaks that have already stained the ceiling or wet the framing

More caulk over failed flashing buys time at best. Ask any roofer whether the repair includes new step flashing and counter-flashing set into the mortar, or only sealant.

Stay off the roof

Chimneys sit at the steepest, hardest-to-reach parts of a roof. Do your checking from the ground and the attic, and leave roof work to a crew with fall protection.

Planning a new roof?

Flashing is often reused during a reroof because replacing it means cutting masonry. Ask whether yours will be, and get the answer in the quote. If the chimney needs masonry work, have it done before the new roof goes on.

4What drives the cost

The price depends on the size of the chimney, the pitch and height of the roof, whether the counter-flashing has to be cut into the mortar fresh, whether a cricket is needed, and how much decking or framing the leak has already damaged. Reflashing during a full reroof usually adds less than doing it as a standalone repair, because the shingles around the chimney are already coming off.

Roofing costRoof replacement

Stain around the chimney?

Talk to a local roofer who will reflash it properly instead of adding another layer of caulk.

877-360-4657

5Questions

Is the leak coming from the brick or the flashing?

Usually the flashing. A stain around the chimney is almost always the roof junction rather than the masonry. A cracked crown or spalling brick can leak too, so have both looked at if reflashing doesn’t stop it.

Can I just reseal the flashing with caulk?

It can slow a leak for a while, but sealant cracks and lets go. Flashing that depends on caulk is the shortcut version, and it fails within a few years.

Will my roofer replace the chimney flashing during a reroof?

Not always. It’s often reused because replacing it means cutting masonry. Ask, and get the answer in writing in the quote.

Should I worry about mold?

If the leak has been going on for a while, check the attic and ceiling. See mold after a roof leak.

Written by Jaylan Jones. I Like To Exterior Services earns a referral fee when a call connects to a contractor. See our business-model disclosure.

877-360-4657